Image showing the DG Labs Coyote e-stim control box

How to Connect the DG Lab Coyote 3 Estim Control Box to E-Stim Systems Electrodes

Quick Summary

The Solution: You need a 3.5mm mono female to 2.5mm mono male adapter to connect E-Stim Systems electrodes and cables (which use 3.5mm plugs) to the DGLab Coyote 3 (which has 2.5mm sockets). This simple adapter bridges the gap and makes the systems fully compatible.

The DGLab Coyote 3 Estim Control Box is a powerful, compact device loved for its wireless features, customizable waveforms, and advanced control options. But if you're pairing it with E-Stim Systems electrodes, you might hit a slight snag: incompatible connectors. Don't worry—this post guides you through connecting these high-end products safely and effectively.

⚠️ Safety First

  • Never place electrodes above the waist unless you are confident in your equipment and abilities.
  • Use only approved adapters and cables to avoid damage or unintended stimulation.
  • Start slow—the Coyote 3 is powerful, and intensity builds quickly, especially with metal electrodes.
  • Clean all components thoroughly after each use.

What You'll Need

Essential Items:

  • DGLab Coyote 3 Estim Control Box (fully charged)
  • E-Stim Systems electrodes (e.g., insertables, pads, or surface electrodes)
  • Connection cables:
  • Conductive gel or lube (for insertables or pads - not needed for self-adhesive electrodes)

Recommended Accessories:

Step-by-Step Setup Guide

1. Understand the Connector Types

  • The Coyote 3's output sockets are 2.5mm mono (not 3.5mm as commonly found in other e-stim gear)
  • E-Stim Systems cables typically terminate in 3.5mm mono plugs
  • This means you need a 3.5mm mono female to 2.5mm mono male adapter to bridge the gap

Important: While mono (2-pole) adapters are best, you can also use stereo (3-pole) adapters.

2. Connect the Cables

  • Ensure the Coyote is switched off.
  • Plug the E-Stim Systems cable's 3.5mm mono plug into the female side of the adapter.
  • Insert the 2.5mm male end into one of the channel outputs on the Coyote 3.
  • Repeat for the second channel if you're using dual-channel play.

3. Attach the Electrodes

  • Connect the electrode(s) to the opposite ends of the E-Stim Systems cables.
  • Apply conductive gel or lube generously if using insertable or skin play electrodes.
  • Position electrodes correctly based on the type (monopolar vs. bipolar) and intended effect.

4. Power On and Configure

  • Turn on the Coyote 3 and access the control menu (locally or via Bluetooth on your phone/tablet through its app).
  • Choose a waveform mode and start at the lowest intensity setting.
  • Slowly increase until the desired sensation is achieved.

Troubleshooting Common Issues

No Sensation Felt

  • Check all connections are secure.
  • Ensure the Coyote 3 is fully charged.
  • Verify you're using the correct adapter type (mono).
  • Apply more conductive gel to the electrodes.

Weak or Intermittent Connection

  • Clean the adapter and cable connections.
  • Ensure the adapter is fully inserted into both the cable and the Coyote.
  • Check for any damage to cables or adapters.

Adapter Doesn't Fit Properly

  • Confirm you have a 3.5mm female to 2.5mm male adapter (not the reverse).
  • Avoid forcing connections - they should fit smoothly.

Wrapping Up

While the DGLab Coyote 3 and E-Stim Systems gear use different connection standards, a simple mono adapter makes them completely compatible. Once connected, you can enjoy the best of both worlds: the Coyote's advanced features and E-Stim Systems' trusted electrodes.

Whether you're an experienced e-stim enthusiast or just starting to experiment with electroplay, setting up your gear properly takes just a few moments and ensures a safer, smoother, and more enjoyable experience.

Next Steps

If you found this blog post useful, let us know using th comment form down below.

Back to blog